Failover PPPOE não funciona.

[Bruno Vicente]

Boa tarde pessoal,

Primeiramente quero dizer que estou usando o EFW 2.4 em um cliente e possuo o seguinte cenário:

Link 1 (Velox PPPOE) Link 2 (Predial Net)

| |

| |

| |

---

EFW 2.4

---

/

|

|

|

Rede Interna

Configurei o link principal (velox) como PPPOE e o secundário (Predial), que é uma conexão “não roteável” como estática na interface uplink.

http://www.brunovic.x-br.com/imagens/main_uplink.png

http://www.brunovic.x-br.com/imagens/uplink1_predial.png

Log do acontecido:

Aug 5 14:35:15 efw uplink[main]: Starting Uplink ‘main’

Aug 5 14:35:16 efw pppd[5462]: Plugin rp-pppoe.so loaded.

Aug 5 14:35:16 efw pppd[5462]: RP-PPPoE plugin version 3.3 compiled against pppd 2.4.4

Aug 5 14:35:16 efw pppd[5462]: pppd 2.4.4 started by root, uid 0

Aug 5 14:35:31 efw pppd[5462]: PPP session is 11440

Aug 5 14:35:31 efw pppd[5462]: Using interface ppp0

Aug 5 14:35:31 efw pppd[5462]: Connect: ppp0 <–> eth3

Aug 5 14:35:31 efw pppd[5462]: PAP authentication succeeded

Aug 5 14:35:31 efw pppd[5462]: peer from calling number 00:90:1A:42:83:8F authorized

Aug 5 14:35:31 efw pppd[5462]: local IP address 189.25.29.59

Aug 5 14:35:31 efw pppd[5462]: remote IP address 200.222.118.26

Aug 5 14:35:35 efw uplink[main]: Notify pppcall about status change of uplink ‘main’. Send OK

Aug 5 14:35:35 efw uplink[main]: Notify uplinks daemon about status change of uplink ‘main’. Status id OK

Aug 5 14:35:35 efw sudo: nobody : TTY=unknown ; PWD=/ ; USER=root ; COMMAND=/usr/local/bin/restartdnsmasq.py –resolv-only

Aug 5 14:35:35 efw uplink[main]: Uplink ‘main’ status: ‘ONLINE’

Aug 5 14:35:36 efw dnsmasq[17932]: read /etc/hosts – 3 addresses

Aug 5 14:35:37 efw dnsmasq[17932]: failed to load names from /etc/openvpn/dnsmasq.hosts.conf: No such file or directory

Aug 5 14:35:37 efw dnsmasq[17932]: reading /etc/dnsmasq/resolv.conf

Aug 5 14:35:37 efw dnsmasq[17932]: using nameserver 200.218.176.8#53

Aug 5 14:35:37 efw dnsmasq[17932]: using nameserver 200.218.176.7#53

Aug 5 14:35:37 efw dnsmasq[17932]: using nameserver 8.8.4.4#53

Aug 5 14:35:37 efw dnsmasq[17932]: using nameserver 8.8.8.8#53

Aug 5 14:35:37 efw pppd[5477]: Terminating on signal 15

Aug 5 14:35:37 efw pppd[5477]: Connect time 0.1 minutes.

Aug 5 14:35:37 efw pppd[5477]: Sent 412 bytes, received 0 bytes.

Aug 5 14:35:37 efw pppd[5477]: Connection terminated.

Aug 5 14:35:37 efw uplink[main]: Stopping Uplink ‘main’

Aug 5 14:35:37 efw uplink[main]: Notify uplinks daemon about status change of uplink ‘main’. Status id FAILED

Aug 5 14:35:37 efw uplink[main]: Uplink ‘main’ status: ‘OFFLINE’

Aug 5 14:35:37 efw uplink[main]: Could not shut down link ‘main’

Aug 5 14:35:37 efw uplink[main]: Notify uplinks daemon about status change of uplink ‘main’. Status id FAILED

Aug 5 14:35:37 efw uplink[main]: Uplink ‘main’ status: ‘OFFLINE’

Aug 5 14:35:37 efw pppd[5477]: Exit.

Reportado em http://bugs.endian.com/view.php?id=3015

Alguma idéia pessoal?

Agradeço desde já!

[Bruno Vicente]

Pessoal,

Aug 5 14:35:37 efw dnsmasq[17932]: failed to load names from /etc/openvpn/dnsmasq.hosts.conf: No such file or directory

Esta linha de erro foi corrigida, agora tenho o seguinte log:

Aug 6 08:42:53 efw uplink[main]: Starting Uplink ‘main’

Aug 6 08:42:53 efw pppd[15506]: Plugin rp-pppoe.so loaded.

Aug 6 08:42:53 efw pppd[15506]: RP-PPPoE plugin version 3.3 compiled against pppd 2.4.4

Aug 6 08:42:53 efw pppd[15506]: pppd 2.4.4 started by root, uid 0

Aug 6 08:43:02 efw kernel: [144460.095008] eth3: no IPv6 routers present

Aug 6 08:43:28 efw pppd[15506]: Timeout waiting for PADO packets

Aug 6 08:43:28 efw pppd[15506]: Unable to complete PPPoE Discovery

Aug 6 08:43:28 efw pppd[15506]: Exit.

Aug 6 08:43:28 efw uplink[main]: Notify uplinks daemon about status change of uplink ‘main’. Status id FAILED

Aug 6 08:43:29 efw uplink[main]: Uplink ‘main’ status: ‘OFFLINE’

Aug 6 08:43:29 efw uplink[main]: Could not successfully call pppd

Aug 6 08:43:29 efw sudo: nobody : TTY=unknown ; PWD=/ ; USER=root ; COMMAND=/usr/local/bin/restartdnsmasq.py –resolv-only

Aug 6 08:43:29 efw kernel: [144487.254131] eth3: link up, 100Mbps, full-duplex, lpa 0x45E1

Aug 6 08:43:31 efw dnsmasq[13391]: reading /etc/dnsmasq/resolv.conf

Aug 6 08:43:31 efw dnsmasq[13391]: using nameserver 200.218.176.8#53

Aug 6 08:43:31 efw dnsmasq[13391]: using nameserver 200.218.176.7#53

Aug 6 08:43:40 efw kernel: [144497.984011] eth3: no IPv6 routers present

[Bruno Vicente]

Continua…

Como não obtive sucesso em resolver esta questão, resolvi deixar o PPPOE por conta do modem e direcionar as conexões dele para o Endian.

Agora, pelo que me parece está funcionando. Os dois links encontram-se UP e a principio o failover está trabalhando da forma correta.

Vou acompanhar o Bugs Endian e ver se alguém mais postará aqui: http://bugs.endian.com/view.php?id=3015

[]’s

[usr]

Pessoal,

estou com 2 Link PPOE e retiro o cabo do link main e não vai para o BACKUP.

Só quando eu desmarco a opção ativo do link main, ai sim passa pro Backup, é bug mesmo?

Tenho que por como o Bruno esta fazendo, o link backup roteado com pppoe e fazendo DMZ pro endian?

Valeu

[usr]

ERRO:

Sep 9 22:51:48 servidor ntpd[15751]: sendto(187.49.33.11): Invalid argument

Sep 9 22:51:51 servidor ntpd[15751]: sendto(200.192.112.8): Invalid argument

Sep 9 22:51:51 servidor ntpd[15751]: sendto(187.49.33.13): Invalid argument

Pessoal, demorou mais foi para o link de Backup, percebi que depois que ele inicializou uns script ai sim ficou o link Backup, seria algo no CRON ou no settings do link backup pra diminuir esse tempo?

Quando eu conecto o cabo na placa do link main, em alguns segundos o link retorna.

Sep 9 23:01:00 servidor fcron[23768]: Job [ -x /bin/run-parts ] && run-parts –report /etc/cron.hourly started for user root (pid 23769)

Sep 9 23:01:02 servidor fcron[23768]: Job [ -x /bin/run-parts ] && run-parts –report /etc/cron.hourly completed

[pontofraco]

Alguem pode ajudar nós?

[fdfelix]

Poxa, nenhuma novidade sobre esse caso?

[Autor]

Posts